Installation Debian 3.0:
1. Put the Debian CD #1 in the Windows system CD drive and a blank formatted floppy in the floppy drive.
2. Open a DOS window and switch to the CD drive. On most systems this will be the D: drive so type in the letter D followed by a colon and press Enter.
3. Go to the directory containing the disk creation program by typing in the following at the DOS prompt: cd distswoodymaindisks-i3863.0.23-2002-05-21dosutils (The part of the path in blue may be different on your system. Use Windows Explorer to go down the directory tree on your CD to verify the above path.)
4. If your A: drive is a 1.44-meg 3.5-inch floppy, enter the following two commands to create the two floppies: rawrite2 -f ..images-1.44rescue.bin -d a (insert the second floppy) rawrite2 -f ..images-1.44root.bin -d a
5. Label the two disks "Boot Disk #1" and "Boot Disk #2" in the order they were created. If your A: drive is a 1.2-meg 5.25-inch floppy drive, replace the blue part of the above commands with images-1.20 Now that you've got everything you need you can go to the system you'll be installing Debian on and begin the installation procedure.
1. Insert CD #1 into the CD-ROM drive and boot the system off of it. In the case of a non-bootable CD-ROM drive you still want to insert CD #1 in the drive but also insert the floppy Boot Disk #1 in the A: drive and boot the system. (You'll be prompted for the floppy Boot Disk #2 during the boot process.) The Welcome screen appears with a boot: prompt at the bottom. At this prompt, type in: vanilla and hit Enter. (If you're booting off a floppy you'll want to enter "linux vanilla" - without the quotes.) You'll see a lot of dependency errors as the kernel loads but you can disregard these. The Release Notes screen is displayed with Continue highlighted so hit Enter and the Installation Menu will appear. The Installation Menu has two parts - upper area has a Next: and Alternate: and possibly an Alternate1: selection - lower part is the steps that you will progress through using the Next: selection.
2. If your hard-disk has existing partitions blow them away now (this includes any existing Linux partitions if you're redoing an install): * Arrow down to Alternate1: Partition a Hard Disk and press Enter to run the cfdisk partitioning utility. If you're installing Debian onto the first hard-drive, highlight /dev/hda (for IDE drives) or /dev/sda (for SCSI drives). If you only have one hard-drive it will already be highlighted. Pressing Enter will display a screen about Lilo limitations. If you have an older system (which will have an older BIOS) you should read this. * Pressing Enter with Continue highlighted will start cfdisk and the existing partitions will be displayed. (The up and down arrow keys will hightlight partitions in the upper part of of the cfdisk display. The left and right arrow keys highlight the available menu selections in the lower part of the display.) Use the arrow keys to highlight them and select Delete. After all partitions have been deleted, be sure to select the Write selection to update the partition table or nothing will change. * After writing the updates to the drive's partition table you'll be back at cfdisk's main screen. Highlight the Quit selection and press Enter to return to the installation menu. * When you use cfdisk to remove existing partitions you "jump ahead" in the installation steps so you'll have to take a step back at this point. Back at the installation menu, arrow down to Configure the Keyboard and press Enter. This will put you back at the correct place in the installation routine so go to the next step in this procedure.
3. With the Next: Configure the Keyboard highlighted, press Enter and U.S. English (QWERTY) will be highlighted. Just press Enter if this is your desired selection and you'll be returned to the installation menu with the Next: step highlighted.
4. This next step partitions the hard-drive. With the Next: Partition a Hard Disk selected press Enter. * The first screen displays the list of connected hard-drive(s). Usually there's only on
1. Put the Debian CD #1 in the Windows system CD drive and a blank formatted floppy in the floppy drive.
2. Open a DOS window and switch to the CD drive. On most systems this will be the D: drive so type in the letter D followed by a colon and press Enter.
3. Go to the directory containing the disk creation program by typing in the following at the DOS prompt: cd distswoodymaindisks-i3863.0.23-2002-05-21dosutils (The part of the path in blue may be different on your system. Use Windows Explorer to go down the directory tree on your CD to verify the above path.)
4. If your A: drive is a 1.44-meg 3.5-inch floppy, enter the following two commands to create the two floppies: rawrite2 -f ..images-1.44rescue.bin -d a (insert the second floppy) rawrite2 -f ..images-1.44root.bin -d a
5. Label the two disks "Boot Disk #1" and "Boot Disk #2" in the order they were created. If your A: drive is a 1.2-meg 5.25-inch floppy drive, replace the blue part of the above commands with images-1.20 Now that you've got everything you need you can go to the system you'll be installing Debian on and begin the installation procedure.
1. Insert CD #1 into the CD-ROM drive and boot the system off of it. In the case of a non-bootable CD-ROM drive you still want to insert CD #1 in the drive but also insert the floppy Boot Disk #1 in the A: drive and boot the system. (You'll be prompted for the floppy Boot Disk #2 during the boot process.) The Welcome screen appears with a boot: prompt at the bottom. At this prompt, type in: vanilla and hit Enter. (If you're booting off a floppy you'll want to enter "linux vanilla" - without the quotes.) You'll see a lot of dependency errors as the kernel loads but you can disregard these. The Release Notes screen is displayed with Continue highlighted so hit Enter and the Installation Menu will appear. The Installation Menu has two parts - upper area has a Next: and Alternate: and possibly an Alternate1: selection - lower part is the steps that you will progress through using the Next: selection.
2. If your hard-disk has existing partitions blow them away now (this includes any existing Linux partitions if you're redoing an install): * Arrow down to Alternate1: Partition a Hard Disk and press Enter to run the cfdisk partitioning utility. If you're installing Debian onto the first hard-drive, highlight /dev/hda (for IDE drives) or /dev/sda (for SCSI drives). If you only have one hard-drive it will already be highlighted. Pressing Enter will display a screen about Lilo limitations. If you have an older system (which will have an older BIOS) you should read this. * Pressing Enter with Continue highlighted will start cfdisk and the existing partitions will be displayed. (The up and down arrow keys will hightlight partitions in the upper part of of the cfdisk display. The left and right arrow keys highlight the available menu selections in the lower part of the display.) Use the arrow keys to highlight them and select Delete. After all partitions have been deleted, be sure to select the Write selection to update the partition table or nothing will change. * After writing the updates to the drive's partition table you'll be back at cfdisk's main screen. Highlight the Quit selection and press Enter to return to the installation menu. * When you use cfdisk to remove existing partitions you "jump ahead" in the installation steps so you'll have to take a step back at this point. Back at the installation menu, arrow down to Configure the Keyboard and press Enter. This will put you back at the correct place in the installation routine so go to the next step in this procedure.
3. With the Next: Configure the Keyboard highlighted, press Enter and U.S. English (QWERTY) will be highlighted. Just press Enter if this is your desired selection and you'll be returned to the installation menu with the Next: step highlighted.
4. This next step partitions the hard-drive. With the Next: Partition a Hard Disk selected press Enter. * The first screen displays the list of connected hard-drive(s). Usually there's only on
2 comments:
sok you now lw`
Switch web hosts if an outage lasts for more than a day. Even if the host explains why the server is down, the most likely reason is that the host did not invest enough into back up plans as far as outages are concerned. Any truly professional web hosts will have ensured that outages will be short and infrequent.
Netwerk Installeren
Server Kopen
Post a Comment